
INDUSTRIAL SPECIALITY LUBRICANT
Specialized oil products
PROCESS & RUBBER OIL
Oil, rubber and ink products
คุณสมบัติของผลิตภัณฑ์
Ballube Rubber Oil is made from selected high-quality refined paraffinic and/or aromatic extract base oils. It is low-to- high viscosity product which aids in rapid ingredient dispersion during mixing operations or process applications requiring good compatibility, thermal and oxidation stability. Their good light stability characteristics provide them to use in white or pastel color products. It is suitable for automobile rubber hoses, rubber seal, rubber band, leather tanning and textile conditioning, etc.

RUBBER OIL

Featured
Heat resistance And resistant to oxidation.
High viscosity index
Clear, light colored oil
And stable color
High flash point and low evaporation rate.
Viscosity Grade of Product
RUB 845
RUB 835
RUB 815
Applications
Used as a raw material in the manufacturing process of the products used. Bring it lubricated into the mixture.Can be used as
Bring it lubricated to drop.
That workload is not heavy.
Product Attribute
Ballube Rub845, Rub Cis made from selected high-quality refined paraffinic base oils. It is low viscosity product which aids in rapid ingredient dispersion during mixing operations or process applications requiring good compatibility, thermal and oxidation stability. Its good light stability characteristics provide them to use in white or pastel color products. It is suitable for automobile rubber hoses, rubber seal, rubber band, leather tanning and textile conditioning, etc.

RUB 845, RUB C

Viscosity Grade of Product
RUB C
Product Attribute
Ballube Rub 835, Oils835 is made from selected high-quality paraffinic base oils. It is medium viscosity oils with very low volatility and heat-aging characteristics. It is used as rubber or process oils during mixing operations or process application requiring good compatibility, thermal and oxidation stability. It is recommended to use as industrial hoses, rubber shock absorber, wire and cable covering, etc.

RUB 835, OILS 835

Viscosity Grade of Product
RUB 835
Product Attribute
Ballube Rub 815, Oils 815 is high-quality refined paraffinic oils which are processed to meet specific aromatic contents and sulphur concentration. The properties of high viscosity oils with very low volatility and heat-aging characteristics. It is suitable for automobile hoses and belts, single ply roofing, flooring, mechanical seals and gasket, footwears. etc.

RUB 815, OILS 815

Viscosity Grade of Product
RUB815
Product Attribute
BALLUBE RUB AP-4 is a special blend high-quality dark green color rubber process oils used as a raw material in rubber processing to enhance homogeneous miscibility of rubber and additive chemicals. Rub-A4P is high solvency and has the properties to improve hardness and tensile strength. It is used as raw materials in rubber process for automotive tire, rubber tube and rubber shoes industries with no hazardous to user as well as environmental friendly.

RUB AP-4

Viscosity Grade of Product
RUB 845
RUB 835
RUB 815
Applications
Using in the tire manufacturing process. Make rubber grinding and easier homogeneous mixing. Suitable for using as a raw material for the tire industry. Not harmful to users and not toxic to the environment.
Product Attribute
Ballube RUB A is Aromatic rubber processing and extender oils for both brand new tire and retread tire industry which has mineral oils as one component of the product. Rub A is also used as once-through lubricating oils.

RUB A

Viscosity Grade of Product
RUB A
Product Attribute
Ballube RUB 110 is Rubber processing and extender oils for rubber compound and suitable for use as carrier oil in the manufacturer of products.

RUB 110

Viscosity Grade of Product
RUB 110
Product Attribute

RT B
BALLUBE RT – B is a unique blend of aromatic mineral oils for rubber processing and extender oils with high viscosity. It is recommended to use as rubber process oil with high viscosity to enhance homogeneous miscibility of rubber and additive chemicals.

Viscosity Grade of Product
RT-B

INK OIL J, INK OIL 400
Product Attribute
Ballube Ink Oil J, Ink Oil 400 is Aromatic base type oils for printing ink carrier industry for black and dark color. It is used for off-set printing

Product Attribute

NAPTHENIC OIL
Ballube Naphtech Oil (BNH 3, 8, 22, 56) are produced with special know-how to hold a great deal of Naphthenic feature. Ballube Naphtech B-series are the best optimum combination of the best refined process, characteristic of crude and selected catalyst to meet OSHA standard and EU PCA below 3% standard. They are specially designed to use as rubber & plastic processing oils, printing ink carrier industry, transformer oils, refrigerating oils, metal working fluids, process oil for binding agents and adhesive tapes, etc.

Product Attribute
Ballube, BL Base, BS2, BS3, BS4, BS6 and BS8 re made from high quality base oils with crystal clear color. Very low sulphur (below 3%), high viscosity index, low volatility with high flash point and excellent thermal and oxidation stability. They can be classified as group III base stock and can be used in a variety of specialty applications where a high degree of purity and chemical stability is required. They are recommended to use in textile application, rubber & elastomer, high speed machine tool spindles and other automated machine.

BL BASE BS2, BS3, BS4, BS6, BS8

Product Attribute
Ballube, Whitech Oil a highly refined white mineral oils which is designed for use in various industrial products and applications where a high degree of purity and chemical stability is required. Ballube, white oils are use as plasticizer for rubber products, as a drawing or forming oils in process of sheet metal or foil, and also use as a base for liquid and aerosol sprays. In textile application, It is used in fiber formulations to reduce abrasion between strands during processing and weaving and to control the build-up of electrical charges and static. They are often used in formulation as processing aids and in many cosmetic product.

WHITE OIL

Concrete Remover
MOLD RELEASE AGENT
Product Attribute

MOLD RELEASE AGENT
Ballube Mold Release Agent a premium water-soluble formwork remover which contain no toxic substances and has no adverse effects on either concrete or formwork. They are applicable for concrete construction mold release as tile mold release or other concrete form remover. Film of the remover is reinforced by use of special additive and the remover applied to the formwork dries fast, obtaining stronger removing power due to special manufacturing methods. Concrete products after remover are not colored and lead to a high quality smooth and beautiful product surface.

Featured
Dilute Mold Ease with water and slightly brush or spray on the dry and clean formwork, leave it 10-30 minutes before casting concrete.
Applications
Do not apply Mold Ease left overnight
Dilute with water and mix well before use
Note : Mold Ease composed by chemical component therefore, wearing rubber gloves is recommended. This product can be mildly irritating to skin so, avoid prolonged contact, it causes skin irritation. Provide adequate ventilation. Close the lid after use
คุณสมบัติของผลิตภัณฑ์
เป็นผลิตภัณฑ์ทาแบบชนิดผสมน้ำคุณภาพสูง เมื่อผสมน้ำจะมีสีขาวคล้ายน้ำนม สามารถใช้ได้ดีกับแบบทุกชนิดไม่ว่าจะเป็นไม้ หรือโลหะ และอื่นๆ

MOLD RELEASE AGENT-J

Product Attribute
Ballube Mold Release Agent J provide a premium water-soluble formwork remover which contain no toxic substances and has no adverse effects on either concrete or formwork.

MOLD RELEASE AGENT J

Applications
They are applicable for concrete construction mold release as tile mold release or other concrete form remover. Film of the remover is reinforced by using of special additive and the remover applied to the formwork dries fast, obtaining stronger removing power due to special manufacturing methods. Concrete products after remover are not colored and lead to a high quality smooth and beautiful product surface
Product Attribute
Ballube Mold Release Agent JRMis a special blend product in form of emulsifier / milky water which provides for the easy of wooden, metal or steel concrete construction mold / forms so that a high quality smooth concrete finish can be obtained.

MOLD RELEASE AGENT-J RM

Applications
The product is specially designed for use on both wooden and steel forms and their preservative action can also reduce wear and prolonged form life.
Product Attribute
Ballube Mold Release Agent J 169 This mold release agent contains special new material with chemical additive and water soluble. It works well with all kinds of formwork; wooden or steel. Ensure fair faced concrete finish.

MOLD RELEASE AGENT J 169

Applications
Apply for brushing wooden or steel for concrete formworks for easy releasing formwork. Dilute with water in the ratio of 1:5. Slowly pouring the liquid into water and mix those together until the color turn to milky white. After that, slightly brush or spray on the dry and clean formwork before casting concret
Do not apply BALLUBE MOLD RELEASE AGENT J 169 left overnight
Dilute with water and mix well before use
Note: Ballube Mold Release Agent J169 composed by chemical component therefore, wearing rubber gloves is recommended.
Product Attribute
Ballube Mold Release Agent J 285 is oil-based mold release agents (no water) for releasing concrete surface out of formworks, provide easy release of formwork and ensure fair faced concrete finish. Extend the life cycle of the wooden formworks and no staining.

MOLD RELEASE AGENT J 285

Featured
provide easy release of formwork and ensure fair faced concrete finish. It forms the thin film barrier between the formwork and help the concrete flow well when pouring and the surface will not be honeycombed. The use of MERTIRE KOJIMA 921 extends the life cycle of the steel formwork substantially. The liquid could protect the rust and clean the formwork. In case of wooden, BALLUBE MOLD RELEASE AGENT J 285 would also protect the wood from absorbing concrete.
Viscosity Grade of Product
RUB 845
RUB 835
RUB 815
Applications
Brush or spray on the dry and clean formwork before casting concrete.
Do not apply BALLUBE MOLD RELEASE AGENT J 285 left overnight
Dilute with water and mix well before use
Note : Ballube Mold Reease Agent J 285 composed by chemical component therefore, wearing rubber gloves is recommended. This product can be mildly irritating to skin so, avoid prolonged contact. It causes skin irritation. Provide adequate ventilation. Close the lid after use
Product Attribute
Ballube Mold Release Agent J 801 is water-soluble mold release agents, having high output after dilution with water result to cost reduction. When mixing, it would turn to milky white color. After dilution, its coating film would not react with the bond of concrete to forming materials. It can be used with all types of forms: steel, aluminum, woods and plastics by spraying or painting. It is used to release concrete surface out of formworks such as such as Precast Concrete Wall Panel, Precast Concrete Fence, foundation piles, floor sheet concrete etc.

MOLD RELEASE AGENT J 801

Featured
Provides a quick, positive release of formwork
Protect metal surfaces against corrosion
Easily to soluble in tab water or underground water
Able to leave it up for long time after mixing with water without the separation of the liquid
No staining on the framework of materials, unlike what made from the old base oil
It drastically reduces the incidence of formwork and high quality surface finishes to concrete, no dusting
No skin irritation. High output after dilution with water and cost saving
It can be used with the
injection spray
Made of high quality of materials, safe without harm to users
Applications
Dilute with water according to the recommended ratio and mix well until melty all white. After that, slightly brush or spray on the dry and clean formwork and leave it until the stains disappear. Then the concrete is prepared after the oil film is formed.
The mixture must be stirred well before using
If the concrete is poured while the solution does not form the film, it will cause the concrete to stick to the mold due to a large amount of water-based admixture. So unreacted film can absorb into concrete. As a result, it is difficult to remove workpieces from castings. And there will be a moldy cast.